Asenqua Tech is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

In this post, we will discuss how you can troubleshoot a Wii Remote that does not turn on. Usually, a Wii Remote won’t respond or turn on because of dead batteries. However, there could be other reasons such as corrosion of the battery holder, misconfigurations in the hardware, etc. Once you have pinpointed the problem, it shall be easy to understand which solution amongst the ones listed below is the most appropriate.

Let us go through the solutions one at a time.

Solution 1 – Turn the remote upside down

Trying holding the Wii Remote upside-down with the buttons pointing downward may help if your Wii remote won’t turn on or doesn’t respond properly.

In order to remove any dust that may have accumulated between the buttons and the electrical circuit board within the remote, tap it three times against the palm of your hand with hard pressure.

Push one of the buttons on the remote control while holding it upright. It’s possible that the problem will persist and that you will need to review the device configuration.

Solution 2 – Check hardware configuration

First, open the battery door on your Wii Remote to check the hardware configuration. Ensure that your Wii Remote has two new “AA” batteries or a fully charged battery pack before you begin using the system. The battery’s metal components and connectors should also be checked for corrosion.

Using a cotton swab, clean the remote’s battery element/connectors if you notice corrosion on them.

Make sure the Wii wireless sensor bar is correctly attached and positioned as well. Check to see that the sensor bar wire is firmly placed into the back of your Wii.

For the Wii Remote to communicate with the gaming system, it must be placed above or below your television.

You can test the Wii sensor bar by standing three feet away from it and pointing your Wii Remote at it. Get at least five or six feet away from the gaming system and try using the remote control again, if the former step does not work.

Candles, other remote controls (TV/cable box) and wireless computer devices/cellular phones should be moved away from the game system/Sensor bar. It’s also a good idea to keep the drapes or blinds closed if there is any sunlight streaming through a window.

Solution 3 – Resynchronize/Reset the Wii Remote

• Press the Power Button on the Wii console to turn it on, then plug it in.
• Open the cover on the SD Card Slot on the front of the Wii. In a Wii mini, the SYNC Button is on the left next to the battery pack. In this picture, the SYNC button is a darker red than the console, but it’s the same colour.
• When you want to sync your Wii Remote, you need to remove the battery cover on the back of it.
• In some Wii Remotes, the battery cover comes off, so you can push the SYNC Button with a tool on your wrist strap, which has a hole. There is no need to take off the battery cover with this model in order for you to get to the SYNC Button.
• Synchronize and release the SYNC Button on your Wii Remote to make it work. The LED in front of your Wii Remote will blink when you press and release this button. You can quickly press and release the red SYNC button on the Wii console while the lights are still blinking, but make sure you do it quickly.
• When the Player LED stops blinking and stays lit, the syncing has been done. The LED that is lit up shows the player number (1 through 4).
• This procedure must be done for each new Wii Remote that is added.

Solution 4 – Replace the batteries of the Wii Remote

If the Nintendo Wii Remote won’t turn on, it is possible that the remote has dead batteries. Aftermarket rechargeable batteries or battery packs can be purchased for the Nintendo Wii remotes despite the fact that the Nintendo Wii controllers themselves do not come with rechargeable batteries.

In many cases, this is what individuals do instead of purchasing a large number of batteries for their remotes.

The rechargeable batteries or battery packs can then be recharged whenever the battery is low.

This not only saves money by eliminating the need to purchase batteries, but it also speeds up the process of replacing them.

How do I know what battery level my Wii Remote is at?

If you’ve ever used a Wii remote, you know that knowing the battery level is critical. That would be the last thing you want to happen during a high-stakes sports game or match with friends: You lose the game because of dead remote batteries.

It’s common for most individuals to recharge their batteries when they’re at least 1/4 of the way full. It’s possible to anticipate how long the batteries will last if they keep track of how many hours they’ve been used, at which point they can replace the batteries every 25 hours or so.

Pressing the home button on the Wii remote that is synced with the gaming console will tell you how much battery life is left in your remote. Select the Wii remote settings option from there.

Here, you’ll be able to see the battery level of all linked remotes on the bottom of the screen.

A full charge is indicated by four bars, with one bar being the lowest charge that may be read.

As soon as your battery reaches one bar, it’s always a good idea to change the batteries or recharge the battery pack and keep going.

What batteries are used for the Wii remote?

After purchasing a Wii, you may question what batteries you will need for the Wii controller. Although most game controllers utilise AA batteries, AAA batteries are becoming more widespread.

Many people may assume that the Wii remotes require a separate battery pack because they were manufactured in Japan, however this is not the case.

AA batteries are the ones that power the Wii remote controller. The Wii remote should only be powered by alkaline batteries.

There is no need to use four AA batteries, because the remotes are smaller than most other gaming controllers.

How long do rechargeable batteries last?

When using a remote control, rechargeable batteries only last a few hours, but many people want to know how long they can last and if it’s worth the money to buy rechargeable batteries instead of conventional batteries.

As AA batteries can be purchased for a dollar at most dollar stores, many people wonder if it is more cost-effective to buy reusable batteries rather than just buying the cheap ones.

Because of this, many people are interested in finding out how long the batteries in their remote control last and how long they may anticipate to last.

If properly cared for, a rechargeable battery can last 5 to 7 years. You can save money by getting rechargeable batteries rather than non-rechargeable ones because you’ll be recharging them several times over the course of those years.

Despite the inconvenience of having to remove and recharge the batteries over and over again, it is preferable than having to buy new batteries every time the controller dies..

 

[FIXED] Wii Remote Won’t Sync to Console

In the event that you’ve recently purchased a new Wii remote for your Nintendo Wii but aren’t sure how to set up the new controller, the instructions outlined in this article will be of assistance to you.

You can also use this guide if you have already attempted to sync your remote with your Nintendo Wii, but have run into difficulties and the connection has been unsuccessful.

What is causing your Wii Remote to fail to sync with your Wii? It is possible that your Wii Remote will not connect to your Wii system owing to a low battery or interference issues produced by other infrared and wireless gadgets in close proximity.

So, if you have a Nintendo Wii but are having trouble configuring your remote, follow the instructions stated below.

Preliminary checks:

• Your TV’s top bezel should be the focal point for the sensor bar. Alternatively, you can place it beneath your television, but we prefer the first option best.
• Ten feet is the ideal distance between your remote and your television.
• Turn off any other infrared light sources that may be interfering with the sensor bar’s ability to read.
• In the same room, turn off all of your wifi devices.

Solution 1 – Take off the battery cover and sync the remote

• Remove the remote’s battery cover.
• Press the remote’s sync button. You should be able to watch all the blue LEDs light up and blink.
• You should be able to spot the “sync” button under the SD card slot.
• In order to establish a connection, the remote’s blue LEDs will stop blinking when the console is connected.
• Every Wii console can use the original Wii Remote controllers. It’s important to keep in mind, though, you may only use the Wii Remote that came with your console. The batteries must be inserted before you can utilise additional Wii remotes.

Solution 2 – Get new batteries

There is a chance that the batteries in your remote control have run out and need to be replaced. As a result, the remote will disconnect from the console or it will fail to sync.

New batteries should be installed. Unplug your console’s power line and turn it off, too. For one minute, unplug the gadget. Try to resync your remote again after the console has been turned on.

 

[FIXED] The Cursor Is Not At The Right Place

If the cursor is not pointing where it is supposed to be, below we have listed a few solutions that could help solve the problem.

Solution 1 – Check if the Sensor Bar is obstructed

Keep the Sensor Bar clear of any obstructions. If so, move it to a location where your remote can see it. Make sure that the Wii console’s sensor bar is fully plugged in.

Solution 2 – Check if the Wii Remote is miscalibrated

The misaimed cursor is frequently caused by a Wii Remote that has not been properly calibrated. You can recalibrate your remote control by placing it on a table with the buttons facing down for about 10 seconds.

Use the Wii Remote in the same orientation as your television. After ten seconds, return the Wii Remote to the television.

Go to the Wii’s home screen and check the location of your sensor bar, either below or above your TV, if this does not work.

Solution 3 – Fix the Sensor Screen

If the issue persists, the sensor screen on your Wii Remote may be defective. You will need to install a properly functioning sensor screen if this is the case.

Solution 4 – Scrutinize the motherboard

The Wii Remote’s motherboard is its heart. As soon as you click the power button, the motherboard sends a signal to the Wii Remote that activates the remote.

If you’ve tried everything else, you may have a faulty motherboard. If the motherboard is faulty, you will be required to use a new motherboard and replace the faulty one.

Solution 5 – Check if there is any light too close to the Sensor Bar

Using a Wii Remote’s heat signal, the Wii sensor bar can tell exactly where you’ve pointed it. Avoid placing lamps too close to the sensor bar, as this could cause the cursor to jerk around. To further protect your Wii’s sensor bar, ensure no infrared lamps are present in the same room as it.

 

How Do You Use Your iPhone as a Nintendo Remote Controller?

The iPhone may be used as a remote control for a variety of devices thanks to a variety of apps. It is possible to use your iPhone as a controller for the Nintendo Wii Console thanks to a free application (iFun) made by gaming business SGN. The iPhone’s accelerometer and touch screen are used to control the Wii’s motion.

• When you open the App Store on your iPhone, tap the “Search” tab at the bottom of the main page to begin your search.
• As soon as you type “iFun” into the search box, touch on it to begin searching. Search results will include the iFun option. Install by pressing “Install” on the option. The app will be installed on your iPhone when it’s finished downloading and installing.
• Turn on your Nintendo Wii by pressing the “Power” button on the console.
• When you open the iFun app on your iPhone, tap the “Sync” button. The Wii system option will be displayed on the results screen when the application searches for devices that can be connected to the network.
• Select “Connect” from the Nintendo Wii option.

 

Read More

[FIXED] Wii U Gamepad Won’t Turn On